Networking retrofit bundle
Powerline + PoE Edge Kit
Retrofit networking for PoE cameras, VoIP phones, and access points.
Use the existing electrical path to create a wired network link and deliver PoE at the remote endpoint instead of pulling new cable.
Some retrofit projects do not just need Ethernet in another room. They also need power at the endpoint. This kit is built for that job. It pairs a standard G.hn sender with a PoE-capable receiver so existing electrical wiring can carry the network path while the far-end device gets the PoE power it needs, all without adding a separate injector or pulling new Ethernet through the walls.
Best fit: Best for buyers who need a true sender-and-receiver powerline starter kit with PoE at the far end, not a single adapter and not a data-only starter pair.
A powerline retrofit kit for cameras, access points, and other edge devices that need both data and PoE.
Quick answer
- What this bundle solves
- It solves the double requirement at the endpoint by bundling the initial G.hn data path and the PoE-powered receiver into one clearer retrofit decision.
- Who this bundle is for
- IP cameras, wireless access points, VoIP phones, and other edge devices that need both wired backhaul and PoE power in a room where new Ethernet is not the preferred retrofit path.
- Why buy this as a bundle instead of separate products
- Buying this as a bundle is better than piecing it together because it removes three separate decisions at once: the first powerline sender, the matching powered receiver, and the far-end PoE requirement.
Who should not start here
This bundle is not the right first click if the real job is broader than the blocker this page solves, if platform state is already resolved in a different direction, or if the project has already moved into custom, trade, or multi-zone scope.
- Do not start here if the compare-next path is actually the cleaner fit.
- Do not start here if the site already has a different platform state than this bundle assumes.
- Do not start here if the job is no longer a one-bundle decision.
Compare next or escalate
If this bundle looks close but not exact, use the compare path first. If the job includes more than 3 zones, multi-door or multi-unit rollout, trade or commercial scope, whole-home planning, or a route that still feels unclear after one compare step, use project pricing instead.
Who this bundle is really for
Buyer fit
Best for buyers who need a true sender-and-receiver powerline starter kit with PoE at the far end, not a single adapter and not a data-only starter pair.
Target persona
A retrofit-minded buyer who wants a cleaner way to place a PoE device in a garage, outbuilding, office, or remote room without opening walls.
Project fit
Use this as the first powerline-plus-PoE kit when the goal is to place a PoE device in another room over existing electrical wiring.
Why this bundle exists
This bundle exists to give buyers the real starting point for powerline-plus-PoE networking: one sender near the router and one PoE receiver at the destination device.
Use this when the remote endpoint needs both data and PoE now, then expand later with additional compatible G.hn nodes if more rooms need the same path.
Included products
Includes the two matching adapters that create the first wired retrofit link and deliver PoE at the remote endpoint.
One G.hn pass-through sender and one G.hn PoE receiver for a data-plus-power starter kit.
Included summary: 1 x Comtrend G.hn Wave 2 Powerline Adapter with Pass-Through Outlet (2000Mbps), 1 x Comtrend G.hn Wave 2 Powerline Adapter with PoE+ (2000Mbps).
1 x Comtrend G.hn Wave 2 Powerline Adapter with Pass-Through Outlet (2000Mbps)
1 x Comtrend G.hn Wave 2 Powerline Adapter with PoE+ (2000Mbps)
Requirements and compatibility
These adapters should be plugged directly into wall outlets for best performance. This is a wired-networking retrofit path with PoE at the endpoint, not a Wi-Fi-extender bundle and not a data-only powerline pair.
Compatibility note: This bundle uses the G.hn Wave 2 powerline protocol. The router-side adapter is the standard pass-through sender. PoE is delivered only at the receiver side of the link. If the remote device only needs Ethernet and not PoE, the standard starter pair is the better fit.
Project guidance: A strong fit for single-device edge locations where the endpoint is a PoE camera, phone, or access point. If the endpoint is a PC, TV, console, or other data-only device, the standard starter pair is the cleaner choice.
Install expectation: Plug the pass-through adapter near the router, plug the PoE receiver at the destination room, and connect the endpoint device at the far end. Expand later with additional compatible G.hn nodes if more rooms need the same path.
Not the right fit when: Not the right fit when the endpoint does not need PoE, when the goal is purely better Wi-Fi instead of a wired Ethernet link, or when the property already has usable coax that makes an Ethernet-over-coax retrofit the better fit.
How to choose between this and related options
Choose this when the endpoint is a camera, access point, or other PoE device. Choose the standard powerline starter pair when the endpoint only needs Ethernet, or choose the coax retrofit bundle when usable coax is already available.
Explore the main collection, adjacent decision path, strongest family guide, and nearest bundle alternatives for this lane.
Questions buyers ask before ordering
What makes this different from the standard G.hn starter pair?
The standard starter pair is for data-only endpoints. This bundle is for endpoints that need both the wired network link and PoE power at the far end.
Who should skip this PoE kit?
Skip it if the endpoint only needs Ethernet, if you only want a Wi-Fi boost instead of a wired link, or if your property already has usable coax that makes Ethernet-over-coax the better retrofit path.
Technical details
Built around a two-node G.hn Wave 2 powerline link with a pass-through sender and a PoE-capable receiver for the far-end device.
-
1 x
Comtrend PG-9182PT G.hn Wave 2 Powerline Adapter - 2000Mbps Pass-Through - PG-9182PT
PG-9182PT -
1 x
Comtrend PG-9182PoE G.hn Wave 2 Powerline Adapter - 2000Mbps PoE+ (30W) - PG-9182POE
PG-9182PoE
Need help choosing the right retrofit network path?
Ask before checkout if you want help deciding between standard powerline, PoE edge powerline, or Ethernet-over-coax for your property and endpoint device.